DIY BATH SETUP.

DIY Bath Setup.

DIY Bath Setup.

Blog Article

Schedule Appointment

Every person may have their own individual perception when it comes to How to Install a Bathtub Yourself.


Installing A Bathtub
Mounting a tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is readily easily accessible, the job can relocate speedily; if you have to open up a wall to eliminate the old bathtub and also position the brand-new bath tub, the task is much harder. In either instance, the project is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Make certain you have actually qualified yourself for the work and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is far better to consider employing one before you start. Opportunities are you might need an expert plumber to make tube connections.
This post will certainly aid you install a new tub in your shower room if you have actually currently acquired a new tub and don't need to alter the setup of your previous water pipelines.
Your tools and material checklist ought to make up the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is commonly the instance.
    Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing substance.
    Prior to carrying on to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existent supply pipelines.
    If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Protect the tap in position with the producer given backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous type must be connected to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Setting up the Bathtub


    Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are practical in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
    The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub till the spirit level reads degree.
    To mount faucets, fit the bottom of the outermost flexible tap port to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
    Switch on the water system and also check all joints and new pipework for leaks and tighten them if needed. Fill up the bath tub as well as additionally examine the overflow electrical outlet and the normal outlet for leaks.
    Lastly, repair the bath paneling as explained in the supplier's user's manual. Tiling and sealing around the tub needs to wait till the bathtub has been utilized a minimum of when as this will certainly resolve it into its final setting.

    Planning for the Installment


    To start with, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to avoid pressure on the bath tub.
    Fit the adaptable faucet connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
    Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its last placement.

    Tiling Around the Bathtub


    In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a stiff seal, causing the water to pass through the wall between the bathroom as well as the tiling, resulting in difficulties with wetness as well as possible leakages to the ceiling below.
    You can choose from a range of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealant can fracture relatively early if you do not think about this movement before securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    Hopefully you enjoyed reading our section about How to Install a Bathtub. Many thanks for taking a few minutes to read through our content. Are you aware of anybody else who is excited about the subject? Why not share it. Thanks a bunch for your time. Come back soon.



    Free Quote

    Report this page